• M5-1500X5:
• 5-Channel powersports amplifier attached to mounting bracket
• 11" Power/ground/turn-on & subwoofer output harness (installed)
• 11" Input harness (installed)
• Amplifier power certificate
• RZR19PXP-FSE:
• Two enclosures loaded with 6.5" 2-way Color Optix speakers (attached 5" input/tweeter output harnesses)
• Two 16" tweeter harnesses with inline crossovers
• 2 Rubber caps
• Dash trim piece
• Torx screwdriver
• RZR19PXP-RCA:
• 30" Ride Command active noise reduction interface
• PMX-RGB:
• Color Optix Light controller mounted to bracket (attached 1.5' power/ground/RGB harnesses w/inline 2A ATO fuse)
• M2-TS:
• 2 Tweeters (with attached 12" speaker wire terminated with proprietary plugs)
• 2 Crossovers
• 2 Front flush mount trim rings
• Two M4x25mm Machine screws
• Eight 1-3/4" Stainless steel Allen head screws
• Eight 1" Stainless steel Allen head screws
• Six 3/8" Stainless steel Allen head screws
• 3mm Allen head bit
• Eight 7" Zip-ties
• Installation/Operation instructions (En/ Fr/ Sp/ Others)
• M2WL-8HB:
• Two M2 8" waketower speakers w/stainless steel grilles
• 2 Upper mounting brackets
• 2 Lower mounting brackets
• Four 2.5" - 3.0" rubber shims w/mounting hardware (four 2-5/8" bolts / 4 flat washers / 4 lock washers)
• Four 1.5" - 2.5" rubber shims w/mounting hardware (four 1-3/4" bolts / 4 flat washers / 4 lock washers)
• Two 12" 6-pin wire harnesses w/Deutsch connectors
• 2 Connection cover-plates
• 4 Plastic grommets
• 1/8" Hex bit
• T-45 Torx wrench
• Instruction manual
• Rockford Fosgate Contact information card
• RZR19PXP-M2FWE:
• M2D4-10IB 10" DVC subwoofer with stainless-steel Color Optix grille
• Subwoofer enclosure with attached internal 16" speaker harness
• Add-on enclosure chamber
• 3 Mounting brackets
• Port plug
• RZR19PXP-K4:
• Pre-configured 15' wiring harness with 4 AWG Power/ground wires and inline Maxi fuse holder
• Two 10" foam strips with 3M adhesive backing
• Thirty-two 14" Wire ties
• Twenty-five 8" wire ties
• Ten 6" wire ties with push-fasteners
• Twelve 7" wire ties with clips
• One rubber grommet
• 1.75" Hole saw with bit
• Hardware Pack:
• 2 Moto-can terminal covers
• Allen key
• 100A Maxi fuse
• 1 Tube of grease
• Amp mounting clamp with nut and washer
• Nine 7/8" screws
• Eight 3/4" screws
• Two 3/4" Torx screws
• 4 Speed-clips
• Four 1-1/2" Torx bolts
• Three 25mm Torx bolts
• Six 60mm screws
• 4 Flat-washers
• 2 Lock-washers
• Hex-head bit

Compatibility
M5-1500X5 Amplifier
RZR19PXP-FSE Front Speakers & Tweeters
M2WL-8HB Waketower Speakers
M2D4-10IB Subwoofer & Enclosure
PMX-RGB LED Controller

Compatibility

Polaris Compatibility: The Rockford Fosgate RZR19RCPXP-STG6 audio system can be used with the following 2020-2022 Polaris RZR Pro XP vehicles:

2-Seat:

4-Seat:

Make	Model	Year
Polaris	RZR Pro XP 4	2020
	RZR Pro XP 4 Orange Madness LE	2020¹ ²
	RZR Pro XP 4 Sport	2021-2022
	RZR Pro XP 4 Sport Rockford Fosgate LE	2021
	RZR Pro XP 4 Premium	2020, 2021-2022¹ ²
	RZR Pro XP 4 Ultimate	2021-2022¹
	RZR Pro XP 4 Ultimate Rockford Fosgate LE	2021-2022

¹ Must be factory Ride Command equipped.
² Factory Rockford Fosgate premium audio system must be bypassed.

Note: The Rockford Fosgate RZR19RCPXP-STG6 is not compatible with the following model Polaris RZR vehicles: Turbo R & R4, Turbo R & R4 Premium, Turbo R & R4 Ultimate, Pro R & R4 Sport, Pro R & R4 Premium, Pro R & R4 Ultimate, Pro R & R4 Ultimate Launch Edition.

M5-1500X5 Amplifier

Amp Overview: The Rockford Fosgate M5-1500X5 is a 5-channel powersports amplifier with a rated power output of 100 watts per channel at 4-ohms or 2-ohms for the four main channels, and 400 watts @4Ω/600 watts @2Ω for the subwoofer channel. This Element Ready amplifier can withstand harsh outdoor environmental conditions.

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load with 1% or less Total Harmonic Distortion plus noise (THD+N). CEA-2006 allows consumers to compare amplifiers and receivers under identical conditions. The CEA-2006-rated RMS power output is 100 watts RMS x 4 channels. Additionally the power output is 100 watts RMS x 4 channels into 2Ω and 200 watts RMS x 2 channels bridged (into 4Ω). The subwoofer output is rated for 400W x 1 @4Ω, 600W x 1 @2Ω, and 600W x 1 @1Ω.

Element Ready: Rockford Fosgate's Element Ready Amplifiers are protected against dust, UV rays, and corrosion. Marine-grade, two-part epoxy-coated circuit boards are used to prevent corrosion due to exposure in moist and humid places. In addition, stainless hardware is used to help prevent rust and corrosion of all electrical connections. The M5-1500X5 carries an IPX6 rating, making it impervious to water spray.

Amp Class: The M5-1500X5 features Rockford Fosgate's proprietary Class-AD technology for the front & rear speaker channels and Class-BD for the subwoofer channel. This allows the amplifier to produce more power with less current draw from the vehicle's charging system.

MEHSA 4 Cooling: The amplifier features Rockford Fosgate's MEHSA 4 (Maximum Efficiency Heat Sink Application) technology that reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output circuitry's life span.

DSM (Discrete Surface Mount): High speed robotics are used in the manufacturing process to place 1% tolerance parts and large board traces. DSM improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature.

CLEAN Set-Up: Rockford's integrated level setting technology, CLEAN (Calibrated Level Eliminates Audible Noise), replaces sophisticated test equipment with input/output clip LEDs, allowing you to match the source unit's output to the amp's gain, and optimize the amp's output. The input clip indicator works in conjunction with the audio source volume, illuminating red when the source reaches its clipping point. The output clip indicator works in conjunction with the input level dial on the amp, illuminating the appropriate color depending on the audio content used for the setup.

PRESET: The M5-1500X5 features Rockford Fosgate's PRESET setting (On/Off) that eliminates the need to set-up the amplifier when used with a compatible Rockford Fosgate ATV/UTV audio kit. When set to On, the PRESET circuitry automatically optimizes the front, rear, and subwoofer input levels, Punch EQ, and crossover settings. If manually setting these adjustments, the PRESET switch should be set to the Off position. Individual PRESET switches are provided for the front, rear, and subwoofer outputs.

Input Level: The amplifier has dual input level controls for the front and rear channels, conveniently accessible from the top. To accommodate the varying range of signal levels from today's factory and aftermarket radios, the input levels are adjustable from 150mV to 12V. A small flat-head screwdriver (not supplied) is needed to adjust the levels.

Crossover: The amplifier has three built-in crossovers for the front, rear, and subwoofer channels. All three crossovers are variable from 50Hz to 250Hz with a slope of 12dB/octave. The front and rear channels can be independently set to high-pass, all-pass (full range), or low-pass operation, while the subwoofer channel is set for low-pass operation. The rotary frequency settings can be adjusted with a small screwdriver.

Punch EQ: The amplifier has two Punch EQ functions (for front and rear) that change with the crossover switches. When the crossover is set to low-pass, the Punch EQ acts as a variable bass boost; 0 to +18dB at 45Hz. When the crossover is set to high-pass, the Punch EQ acts as a variable treble boost, 0 to +14dB at 12.5kHz. When the crossover is set to all-pass, both the bass and treble boost circuits are active. The subwoofer channel's Punch EQ acts as a variable bass boost only.

Wiring Connections: All of the M5-1500X5's wiring connections are ready to accept the included 4 AWG amp wiring kit harnesses, including RCA signal input and speaker output connections.

RZR19PXP-K4 Amp Wiring Kit: The Rockford Fosgate amplifier wiring kit has been designed specifically for mounting a single M5-1500X5 powersports amplifier into select Polaris RZR UTVs, both 2-seat and 4-seat models. The wiring kit includes pre-cut and loomed 4 AWG power and ground wires along with signal input and speaker output leads that are designed to plug directly into an M5-1500X5 amplifier and the factory wiring.

RZR19PXP-RCA: The Rockford Fosgate sound system includes a Ride Command 3-way active noise reduction interface that attaches inbetween the signal leads from the factory radio and the inputs on the M5 amplifier.

Amplifier Mounting: An amplifier mounting plate is provided and comes pre-installed to the M5-1500X5 amplifier. This allows the amp to be mounted in the left front outer dash area.

RZR19PXP-FSE Front Speakers & Tweeters

Front Speaker Overview: The Rockford Fosgate powersports package includes a pair of 6.5" 2-way speakers pre-mounted in Color Optix enclosures designed to mount in the front factory speaker location.

• Weather: The 6.5" 2-way speakers are made weather resistant with the Santoprene front isolation spider, connecting the tweeter housing and woofer cone assembly.
• Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the speaker's motor structure, voice coil alignment, and suspension to yield the best possible performance.
• CEA-2031 Compliant: The power handling specifications conform to the CEA-2031 industry standards; meaning the speaker has the capacity to handle its rated power under continuous demand, not just for an instant.
• VAST Surround: The Vertical Attach Surround Technique (VAST) increases a speaker's effective radiating cone area without increasing the size of the basket. The surround is made of Santoprene rubber.

M2-TS Tweeters: The Rockford Fosgate sound system includes a pair of M2-TS tweeters that get mounted in the front speaker enclosures along with the 6.5" speakers. This allows the factory tweeters (if equipped) to remain functional along with the new ones.

• Marine Use: The Tweeters are tested to ensure they meet or surpass the ASTM-G154 standard for UV stability, the ASTM-B117 standard for salt/fog resistance, the ISO60068-2-64 standard for vibration, and the IPX6 water intrusion rating.
• Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the tweeter's motor structure, voice coil alignment, and suspension to yield the best possible performance.
• Crossovers: The system includes two passive, high-pass crossover networks. The slope is 18 dB/octave and the crossover point is 3000 Hz. Each crossover's output is terminated with a plug that mates with the plug in the tweeter.

Front Speaker Enclosures: The Rockford Fosgate RZR19PXP-FSE Color Optix front speaker enclosures are constructed of reinforced polymer along with a UV resistant finish and are roto-molded for a seamless speaker mount that's both lightweight and durable. The speaker enclosures are also color and texture matched to the vehicle's interior and are a direct bolt-in using the OEM mounting holes. Each enclosure provides a direct plug-in harness for the included speaker wiring, along with Color Optix RGB LED wiring connections.

M2WL-8HB Waketower Speakers

Wakeboard Tower Speakers: The Rockford Fosgate M2WL-8HB Color Optix marine-grade waketower speakers each feature an 8" 2-way speaker mounted in a sealed enclosure that's designed for the marine environment. Both speaker and enclosure are treated with UV inhibitors and conform to UV and Salt-Fog industry standards. The waketower speakers feature Rockford's Color Optix RGB LED lighting that can illuminate the cone area as well as the rear logo (RGB controller sold separately).

Two-Way Design: The Rockford Fosgate M2WL-8HB waketower speakers come loaded with an M2 Series 2-way marine speaker. Both horn tweeter and woofer are treated for UV radiation and salt-fog resistance for maximum lifespan.

• 1" Horn Tweeter: The M2WL-8HB features a 1" high-efficiency horn tweeter that can project crisp, clear highs in a narrower, more focused pattern than a dome tweeter, letting skiers and wakeboarders enjoy the music while on the water. The 1" horn tweeter is coaxially mounted to the 8" woofer.
• 8" Woofer: The 8" woofer is made of a mineral filled, injection molded polypropylene material and features integrated UV inhibitors protecting it from sun exposure. This is attached to the UV stable injection molded frame assembly by a VAST vertically attached surround, designed to increase the cone's effective radiating area by up to 25%.
• ICC Crossover: The ICC (Integrated Concealed Crossover) protects the crossover by concealing it inside the basket. This Integrated 12dB/octave sealed crossover features a built-in protection circuit.
• Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the speaker's motor structure, voice coil alignment, and suspension to yield the best possible performance.

Power: Each Rockford Fosgate marine speaker can handle up to 300W RMS (1200W peak).

Color Optix: The M2WL-8HB marine speakers feature Rockford Fosgate's Color Optix RGB LED lighting integrated into the enclosure, allowing the speaker cone and rear logo to be illuminated. Control of the RGB LED lighting is done using the included Rockford Fosgate PMX-RGB Color Optix controller in conjunction with the free RF Connect App on your smartphone or tablet. This lets you select from a wide range of colors along with adjusting brightness and scrolling speed.

Rugged Enclosure: The enclosure is constructed of high density ASA material and coated with a UV inhibitor to withstand the harsh marine environment.

IPX6: The marine speakers carry an IPX6 waterproof rating, making them impervious to water spray from all directions.

Mounting: The Rockford Fosgate M2WL-8HB speakers are designed to be mounted to wakeboard tower tubing ranging from 1.5" - 3.0" in diameter. Stainless steel mounting clamps are included that provide up to 360° of rotation for optimal speaker aiming, and include rubber shims for a secure fit. The illuminated rear logo features Rockford Fosgate's 3DIL technology, allowing it to be rotated up to 360° for proper orientation after mounting.

Grilles: The M2WL-8HB wake tower speakers are protected by stainless steel grilles (installed).

Wiring: Speaker and RGB connections to the M2WL-8HB speakers are made through the two provided 12" 6-pin wire harnesses with Deutsch marine-grade connectors. Two connection ports are available on the speaker enclosures; one hidden inside the mounting clamp area, for a clean "no-wire" look, the other on the outside of the enclosure. Protective covers are provided for both ports when not using.

Rear Speaker Wiring: The RZR19RCPXP-STG6 kit includes pre-configured wire harnesses for connecting the rear wake tower speakers to the amplifier. Each harness is terminated with Deutsch marine-grade connectors that are designed for "plug-and-play" installation. All pre-configured wire harnesses are Element Ready to withstand even the harshest outdoor environments.

M2D4-10IB Subwoofer & Enclosure

Marine Tested: Rockford Fosgate uses industry standard tests (ASTM B117 salt/fog and ASTM G154 UV) to ensure the M2D4-10IB subwoofer is durable in the difficult marine environment.

Impedance Switch: A switch on the input terminal allows you to easily change the subwoofer's impedance between 2Ω and 8Ω, internally changing between wiring the dual 4Ω voice coils in parallel and in series. (The connected amplifier should be off when changing the impedance.) The power handling is the same for either setting; 400 watts RMS/1600 watts peak.

Infinite-Baffle Operation: The M2D4-10IB is optimized for infinite-baffle operation (free air) so it can be installed in a variety of locations, without the need for a dedicated enclosure.

LEDs: There are red, green, and blue LEDs on the back of the grille to create a glow on the woofer cone. The LEDs can be powered individually, or in any combination you like. Depending on what combination of LED wires is connected, they light red, green, blue, yellow, pink, aqua, or white. The LEDs can be controlled using the included Rockford Fosgate PMX-RGB LED Controller. An LED power wire harness is included with a 4-pin waterproof Deutsch DT Series connector that plugs into the subwoofer frame.

Speaker Terminals: In addition to standard male quick slide terminals, the subwoofer also has a 2-pin waterproof Deutsch terminal. A speaker wire harness with a 2-pin waterproof Deutsch DT Series connector is not included.

VAST Surround: The Vertical Attach Surround Technique (VAST) increases a speaker's effective radiating cone area without increasing the size of the basket.

Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the speaker's motor structure, voice coil alignment, and suspension to yield the best possible performance.

Stainless Steel: The mounting hardware is stainless steel to resist corrosion.

RZR Subwoofer Enclosure: The RZR19PXP-M2FWE 10" subwoofer enclosure is a roto-molded, composite-blend subwoofer enclosure which is designed to be a direct fit for select Polaris RZR model ATVs. The enclosure's texture and color is matched to the ATV's interior and is up to 40% lighter than previous generation enclosures. The subwoofer enclosure mounts under the passenger side dash and bolts directly to the factory mounting holes.

PMX-RGB LED Controller

Overview: The Rockford Fosgate PMX-RGB Color Optix controller lets you illuminate and control up to 8 Rockford Fosgate Color Optix marine speakers and subwoofers. Featuring a completely encased housing, rubberized wiring, and Element Ready watertight connectors, the PMX-RGB is IPX7 waterproof certified, making it impervious to even the harshest marine environments.

App Control: The PMX-RGB can be controlled from your smartphone using Rockford Fosgate's proprietary RF CONNECT App, available from the Apple App and Google Play stores. After connecting your smartphone wirelessly to the PMX-RGB controller, you'll be able to choose from 30 different color scrolling options or choose a fixed color from the color wheel. Scrolling speed and brightness controls are also available for customizing the lighting.

Plug&Play: The Rockford Fosgate PMX-RGB controller features easy configuration and connection via proprietary Element Ready connectors that provide a secure, watertight seal. It features 8 individual 17" RGB output cables for lighting up to 8 Rockford Fosgate Color Optix marine speakers (maximum 2A total current draw).

Mounting & Powering: The PMX-RGB controller includes a bracket for mounting it behind the radio in the dash area. Pre-attached harnesses allow for quick connection to the included RGB wiring harnesses.